2.2 供热介质及其参数
2.2.1 供热介质 heating medium
在供热系统中,用以传送热能的媒介物质。
2.2.2 低温水 low-temperature hot water
水温低于或等于100℃的热水。
2.2.3 高温水 high-temperature hot water
水温超过100℃的热水。
2.2.4 供水 supply water
从热源供给热力站或热用户的热水。
2.2.5 回水 return water
从热力站或热用户返回热源的热水。
2.2.6 生活热水 domestic hot-water
满足民用及公用建筑日常生活用的热水。
2.2.7 饱和蒸汽 saturated steam
温度等于对应压力下的饱和温度的水蒸气。
2.2.8 过热蒸汽 superheated steam
温度高于对应压力下的饱和温度的水蒸气。
2.2.9 凝结水 condensate
蒸汽冷凝形成的水。
2.2.10 二次蒸汽 flash steam
凝结水因压力降低到低于与其温度相对应的饱和压力,再汽化产生的蒸汽。
2.2.11 沿途凝结水 condensate in steam pipeline
蒸汽在管道中输送时产生的凝结水。
2.2.12 补给水 make-up water
由外界向供热系统补充的水。
2.2.13 供热介质参数 parameters of heating medium
表述供热介质状态特征的各种物理量。
2.2.14 供水温度 temperature of supply water
从热源供给热力站或热用户的热水温度。
2.2.15 回水温度 temperature of return water
从热力站或热用户返回热源的热水温度。
2.2.16 设计供水温度 design temperature of supply water
设计工况下所选定的供水温度。
2.2.17 设计回水温度 design temperature of return water
设计工况下所选定的回水温度。
2.2.18 实际供水温度 actual temperature of supply water
运行时的供水温度。
2.2.19 实际回水温度 actual temperature of return water
运行时的回水温度。
2.2.20 最佳供水温度 optimal temperature of supply water
经技术经济分析所确定的供水温度的最佳值。
2.2.21 最佳回水温度 optimal temperature of return water
经技术经济分析所确定的回水温度的最佳值。
2.2.22 设计供回水温差 design temperature difference between supply water and return water
设计供水温度与设计回水温度之差。
2.2.23 实际供回水温差 actual temperature difference between supply water and return water
实际供水温度与实际回水温度之差。
2.2.24 最佳供回水温差 optimal temperature difference between supply water and return water
经技术经济分析所确定的供水温度与回水温度之差的最佳值。
2.2.25 供水压力 pressure of supply water
热水供热系统供水管道中、热源设备出口、热用户入口处的热水压力。
2.2.26 回水压力 pressure of return water
热水供热系统回水管道中、热源设备入口、热用户出口处的热水压力。
2.2.27 设计压力 design pressure
设计工况下供热管道或设备承受的压力。
同义词:计算压力。
2.2.28 工作压力 working pressure
运行工况下供热管道或设备承受的压力。
2.2.29 允许压力 permissible pressure
供热设备、管道及其管路附件允许承受的最大工作压力。
2.2.30 富裕压力 safety pressure redundancy
制定水压图时为了保证热水供热系统安全可靠运行,增加的压力安全裕量。
2.2.31 汽化压力 saturation steam pressure
水在一定温度下从液态变为气态时所对应的饱和压力。
2.2.32 试验压力 test pressure
对供热管道和(或)设备进行强度试验或严密性试验的压力。
2.2.33 供汽温度 temperature of supply steam
蒸汽供热系统供汽管道中、热源设备出口、热用户或用汽设备入口处的蒸汽温度。
2.2.34 供汽压力 pressure of supply steam
蒸汽供热系统供汽管道中、热源设备出口、热用户或用汽设备入口处的蒸汽压力。
2.2.35 过冷度 degree of subcooling
蒸汽供热系统中凝结水的温度低于相应压力下饱和蒸汽温度的数值。
2.2.36 背压 back pressure
蒸汽供热系统中供热设备、疏水器及用热设备出口供热介质的压力。